Flashing Repair Alhambra CA That Stops Leaks Fast

Flashing Repair Alhambra CA is the fastest way to stop water running down your chimney, around a skylight, or through a roof valley. We find the failed metal, seal it with Henry or DAP products, and test it before we leave. If you have a ceiling stain spreading after last week's rain, call (626) 640-8498 and we will get a roofer on your roof today.

Call (626) 640-8498Get a free quote
Flashing Repair
  • Chimney flashing
  • Skylight curbs
  • Roof valleys
  • Written scope firstYou see the estimate before we start
  • Photos of the problemWe show you what we found
  • Clean work areaWe haul away all debris
  • Test before we leaveWater test confirms the fix

What Our Flashing Repair Service Includes

Every flashing repair starts with a full inspection and ends with a water test and photos. The list below covers what is standard on our jobs. If we find something outside this scope, like rotted sheathing or a failed skylight glass unit, we tell you before we do the work and quote it separately.

  • Full Roof InspectionWe check every penetration, valley, seam and wall intersection on the roof, not just the one you called about. A moisture meter and infrared camera confirm the entry point so we fix the actual leak.
  • Old Sealant RemovalWe pull the failed sealant and fasteners with a pry bar and utility knife, then clean the substrate. New sealant over old, dirty material is the number one reason flashing repairs fail early.
  • New Flashing and SealantWe install new metal where needed, set it in roof cement, and finish with Henry or DAP sealant rated for our temperature range. Underlayment goes behind chimney and skylight curbs.
  • Water TestWe run a hose over the repair for 10 to 15 minutes and check from inside the attic. If any water shows up, we keep working until it is dry. You do not pay for a repair we have not verified.
  • Photos and WarrantyYou get before-and-after photos of the flashing and the written warranty terms for the work. If the same seam leaks again inside the warranty window, we come back at no charge.
Flashing Repair

Flashing repair for homes

Homes in Alhambra leak most often at the chimney, skylight or vent pipe, not in the middle of the roof. We lift the shingles or tiles, rebuild the flashing detail, and water-test it before we leave.

  • Chimney flashing reseal
  • Skylight curb rebuild
  • Vent boot replacement
  • Valley metal repair

Flashing repair for businesses

Commercial flat roofs leak at penetrations, seams and parapet walls where the membrane turns up. We repair the flashing detail with compatible material and schedule the work around your tenants.

  • RetailFlat roof vent and curb flashing repairs
  • OfficeParapet and seam flashing work after hours
  • WarehouseTPO and EPDM penetration re-flash
  • RestaurantGrease vent and exhaust curb sealing

Flashing Repair Alhambra CA: What It Actually Fixes

Flashing Repair Alhambra CA is the trade of resealing, re-securing or replacing the metal strips that keep water out of the joints where your roof meets something else. That means chimney walls, skylight curbs, vent pipes, dormer sidewalls and roof valleys. We pull the old sealant, check the metal for rust or lifting, reset it with new fasteners and roof cement, then cover the seam with a fresh layer of modified bitumen or Grace underlayment where the slope calls for it. Most repairs take two to four hours.

Alhambra homes take a beating from both ends of the weather. Summer heat pushes 100 degrees and expands the metal; winter rain and Santa Ana wind cycles pull it back. That constant movement is what opens flashing seams on older tract homes near Garfield Avenue and the hillside streets above Alhambra High. If you have been searching for flashing fixing near me Alhambra after a ceiling stain appeared, the leak is almost always at a penetration, not in the field of shingles.

Flashing fails at the joints, so that is where we look first.

How Our Flashing Repair Process Works

Every job follows the same five steps, whether it is a single vent boot or a full chimney re-flash. You get a clear scope, a set price, and a roof that passes a hose test before we pack up.

  1. Roof Inspection

    Roof Inspection

    We walk the roof with a roof ladder and check every penetration, valley and seam. An infrared thermal imaging camera and moisture meter confirm where the water is actually entering, which is often a few feet uphill from the stain on your ceiling. This takes 30 to 45 minutes.

  2. Written Scope

    Written Scope

    You get a plain-language scope with photos of the failed flashing and a fixed price before we start. No surprise line items. If the metal is reusable, we say so and reseal it. If it is rusted through, we quote replacement.

  3. Removal and Prep

    Removal and Prep

    We lift the surrounding shingles with a pry bar, pull the old fasteners, and clean the substrate down to sound material. Any rotted sheathing gets marked and replaced. This is the step that separates a repair that lasts from one that leaks again next winter.

  4. New Flashing and Seal

    New Flashing and Seal

    New metal goes in, fastened with a nail gun and set in roof cement. We layer Grace underlayment behind chimney and skylight curbs, then finish with Henry or DAP sealant rated for the temperature swings we see here. On flat sections we use TPO or EPDM membrane.

  5. Water Test and Cleanup

    Water Test and Cleanup

    We run a hose over the repair for 10 to 15 minutes and watch from inside the attic. If it is dry, we clean the gutters of debris, magnet-sweep the yard for nails, and hand you photos of the finished work plus the warranty terms.

Tools and Methods We Use on Flashing Jobs

  • Infrared thermal imaging camera

    Maps temperature differences on the roof deck to find trapped moisture and confirm the leak path before we open anything up.

  • Moisture meter

    Reads water content in sheathing, framing and insulation so we know how far the leak has spread and whether the area is drying properly.

  • Roof ladder and fall protection

    Gets us safely onto steep and multi-story roofs so we can inspect and repair flashing details that are hard to reach.

  • Pry bar and utility knife

    Lifts shingles and tiles without cracking them and cuts away old sealant and failed underlayment cleanly.

  • Caulking gun and nail gun

    Applies sealant in a controlled bead and fastens new flashing metal securely to the deck and framing.

  • Hose and tarp

    Water-tests the finished repair and covers active leaks temporarily when a storm prevents a permanent fix.

  • GAF Master Elite installation standards

    We build flashing details to GAF specifications so the repair matches the manufacturer requirements that keep your roof warranty valid.

  • Owens Corning Preferred flashing details

    For Owens Corning roof systems, we follow the published flashing and underlayment details so the repair integrates with the existing roof assembly.

When Alhambra Homeowners Call Us for Flashing

  • A ceiling stain appeared above the fireplace after the first big rain of the season, and it grows with every storm.

    We inspect the chimney flashing, confirm the entry point with a moisture meter, and rebuild the flashing detail. We also check the chimney crown and mortar joints for other water paths. The ceiling stain stops spreading, and you get photos of the repaired flashing plus a water test confirming the leak is closed.

  • Water is dripping around a skylight during heavy rain, and you are not sure if the glass or the flashing is at fault.

    We get on the roof, inspect the curb flashing and sealant, and test with a hose while watching from inside. If the glass unit is also failing, we tell you and quote that separately. You know exactly what failed, the flashing is rebuilt, and the skylight is dry through the next storm.

  • A flat roof addition over the garage has a recurring leak near a vent pipe that nobody has been able to fix.

    We use an infrared thermal imaging camera to map wet areas under the membrane, then repair the flashing detail at the penetration with compatible TPO or EPDM material. The leak stops, the membrane is watertight again, and you avoid a full flat roof replacement.

  • You are selling your Alhambra home and the buyer's inspector flagged rusted flashing at the chimney and vents.

    We inspect every flagged item, repair or replace the failed flashing, and provide photos and documentation of the completed work for your file. The repair items clear, the buyer has documentation, and the sale moves forward without a renegotiation over the roof.

How Flashing Repair Runs in Alhambra

Alhambra sits in a pocket of Los Angeles County where summer heat and winter rain pull roof metal in opposite directions. Afternoon temperatures push past 100 degrees in July and August, then drop into the 40s on winter nights. That swing is what cracks sealant and works fasteners loose on chimney and skylight flashing. Older homes near Main Street and along the streets off Garfield Avenue often have original flashing that has been resealed several times over the decades. Newer tile roofs in the hills have different details but the same failure points at valleys and penetrations. When you call for flashing fixing Alhambra, we bring materials for both: Henry and DAP sealants, Grace underlayment, and TPO or EPDM membrane for flat sections. We work to California Contractor License (C-39 Roofing) standards and pull the right flashing details for your roof type. If you need roof flashing repair in Alhambra CA after a storm, we can tarp the area the same day and return to make the permanent fix.

  • Downtown Alhambra / Main StreetA mix of older commercial buildings and homes with flat and low-slope roofs. Flashing failures here often show up at parapet walls and roof drains.
  • Almansor Park areaMostly single-family homes with asphalt shingle roofs. Chimney and vent boot flashing are the most common leak sources we repair here.
  • Hillside streets above Alhambra HighSteeper roofs with clay tile and occasional slate. Valley and sidewall flashing take the most weather on these elevations.
  • Garfield Avenue corridorOlder tract homes with original flashing that has been resealed multiple times. We often find rusted metal that needs full replacement.
  • Summer heat above 100 degreesExpands metal flashing and dries out sealant beads, which is why we use products rated for high temperature swings and check fastener tightness on every visit.
  • Winter rain and Santa Ana wind cyclesDrives water sideways into flashing joints and pulls at lifted metal. We test repairs with a hose to simulate wind-driven rain, not just overhead flow.

From problem to finished result.

  • Chimney Flashing Rebuild on a 1940s Bungalow

    Before

    A homeowner near Almansor Park had a ceiling stain that grew with every storm. Two prior reseals had failed because the original metal was rusted through and the counter-flashing had pulled away from the chimney wall.

    After

    We removed the old flashing, replaced the rusted metal, and rebuilt the counter-flashing and base flashing with new material set in roof cement and Grace underlayment. A 15-minute hose test showed no water in the attic. The repair cost $640.

    Check the sealant bead at the chimney each fall before the rainy season. If it looks cracked or pulls away from the wall, call us for a reseal before water gets behind it.

  • Skylight Curb Re-Flash in San Gabriel

    Before

    A skylight had leaked for two years and two other roofers had blamed the glass. The actual problem was the curb flashing, where the sealant had dried and cracked and the metal had lifted at one corner.

    After

    We rebuilt the curb flashing with new metal and fresh sealant, then water-tested from the roof while the homeowner watched from the attic. The leak stopped completely. Total job time was three hours.

    Inspect the sealant around the skylight curb every spring. A $150 reseal every few years is far cheaper than replacing the skylight or the ceiling below it.

  • Flat Roof Vent Flashing on a Commercial Building

    Before

    A property manager in Monterey Park had a recurring leak at a vent penetration on a TPO flat roof. Previous patches had peeled because the membrane was not properly cleaned before the patch was applied.

    After

    We cleaned and prepped the membrane, heat-welded a new flashing detail around the vent, and used infrared detection to confirm no other wet spots remained. The repair has held through two rainy seasons.

    Have the flat roof inspected once a year and keep drains and scuppers clear of debris. Standing water is what shortens the life of any flat roof flashing detail.

Flashing Problems We Solve in Alhambra

Most Alhambra flashing calls come down to one of a handful of failures. Here is what we see most often, what happens if you leave it, and how we fix it.

  • Chimney flashing pulling away from the wall

    Chimney flashing pulling away from the wall

    We rebuild the counter-flashing and base flashing, reset it in roof cement, and layer Grace underlayment behind the curb. The chimney gets a water test before we close the job. Wind-driven rain gets behind the metal and runs down the chimney into the attic and ceiling. Left alone, it rots framing and stains drywall within one rainy season.

  • Skylight curb flashing dried out and cracked

    Skylight curb flashing dried out and cracked

    We remove the old sealant bead, check the curb for rot, and rebuild the flashing with new metal and fresh sealant. A hose test confirms the fix from inside the attic. Water seeps around the curb and drips onto the ceiling below. The leak often looks like a skylight glass problem but is actually a flashing failure.

  • Vent boot rubber cracked by UV exposure

    Vent boot rubber cracked by UV exposure

    We replace the failed boot with a new one sized to the pipe, set it in sealant, and check the surrounding shingles for damage. This is one of the cheapest leak fixes on any roof. A cracked boot lets water run straight down the vent pipe into the attic. It is a small part that causes a big, persistent leak.

  • Valley metal rusted through or seal failed

    Valley metal rusted through or seal failed

    We clear the valley of debris, replace or reseal the metal, and reset the surrounding shingles. A hose test at the top of the valley confirms water flows where it should. Valleys carry the most water on the roof. Once the metal or its seal fails, every storm sends water into the attic and down the walls.

  • Flat roof flashing separated at a penetration

    Flat roof flashing separated at a penetration

    We clean and prep the membrane, heat-weld or patch the flashing detail, and reseal the termination. Infrared detection confirms no other wet spots remain under the surface. TPO and EPDM membranes pull away from curbs and vents as they expand. Water pools at the gap and finds its way inside, often showing up far from the actual leak.

We find the flashing leak, fix it, and prove it is dry.

  • Stop the Leak Today

    We locate the entry point with an infrared thermal imaging camera and a moisture meter, then seal it the same visit. Most Alhambra flashing calls are closed out in one trip, so you are not watching the forecast and hoping.

  • Protect Ceilings and Attics

    Water that gets past a chimney or vent boot soaks insulation and stains ceilings. Fixing the flashing stops the damage at the roof line, before it reaches the drywall you would otherwise have to cut out and replace.

  • Save Money Long Term

    A flashing fixing cost Alhambra CA of a few hundred dollars is far less than a full roof replacement. We repair the metal and sealant that failed, not the whole roof, so you keep the shingles that still have life left in them.

  • Handle Emergency Leaks

    When rain is coming through a skylight at 9 p.m., we can tarp the area and return in daylight to make the permanent repair. Emergency Flashing Repair Alhambra CA keeps the water out of your house until we can do the full job.

What you receive

Clear records you can keep and share.

Written scope

Fixed price before work begins

Job photos

Before and after images of the flashing

Water test

Hose test with attic verification

What to know about flashing leaks

Water rarely enters where the ceiling stain appears. It travels along framing and shows up far from the actual roof opening, which is why we trace the path before we repair anything.

  • Stains mislead

    A ceiling stain can sit several feet from the flashing that is actually leaking. We use a moisture meter and thermal camera to find the true entry point.

  • Sealant ages

    Sealant beads dry out and crack after a few summers of heat. A fresh bead at the right time prevents the metal from ever letting water behind it.

  • Metal moves

    Flashing expands and contracts with the temperature every day. Fasteners work loose over time, so we check and reset them on every repair.

Local service area

Roof repair coverage around Alhambra

Not sure if we cover your area? Call and ask. (626) 640-8498

Frequently Asked Questions About Flashing Repair

Still wondering? (626) 640-8498

Local service team

Related Roof Services We Offer

Get Flashing Repair Alhambra CA Scheduled Today

Water at a chimney, skylight or valley will not seal itself, and the next storm is already in the forecast. Call (626) 640-8498 and we will inspect your roof, show you what failed, and give you a fixed price before we start. Most repairs are done in one visit.

Call (626) 640-8498Book an Inspection

Contact Roof Repair Alhambra Pros

Call us at (626) 640-8498 or email [email protected]. We answer the phone during business hours and respond to emergency calls after hours. Same-day estimates are available for most jobs in Alhambra and surrounding areas.

Thanks. Your request is in and the team will follow up shortly.